Looking for the easy way to fix up the accessing issue on your phone after doing a hard reset? Loosing access and facing the (Google Verification) after performing the hard reset is due to FRP lock protection activated. You can bypass this screen only, if you know your already setup Gmail id. Otherwise, either you recover your lost Gmail account or follow up the guide from below to Bypass FRP ZTE Nubia Music.
Disclaimer: We highly recommend you to apply this method only on your own device, if you are not owner of this device, or you found this from some where, you must return to its real owner. This method is for educational purpose only.
Bypass FRP ZTE Nubia Music With (BFT Tool)
-Continue this procedure just through downloading below BFT tool on your computer.
Note: Don’t forget the to disable your any active (@ntivirus tool) from the computer. Otherwise, the file will be removed. You can activate it again right after using this tool.
| ⇒ BFT Tool V1.7 [DOWNLOAD]. |
-This is a free tool, you don’t need to use any user id, simply, click at “Login” button to gain full access to all options of the tool.
-We have to select the correct processor type for your ZTE Nubia Music phone. We are choosing the “0-UNISOC” processor.
-Select the “MANUAL” option and choose the chipset name “[AUTH] SC9863A (64)”.
Get all the Required Drivers
-Click at the “Driver” option from top right corner and then, choose the “Install SPD Driver“. This driver will be downloaded automatically, after that, will show you installation popup window. From there, just install this driver.
-Click again on “Driver” and download another driver named “Install LibUSB Filter Driver“.
-From the installer window, just click to “Next” and install it on your PC.
-After installation is completed, you will have a (LibUSB filter driver) screen. From there, click at > Install a device filter > Next.
-Once you see the same screen as shown in below image. Just turn off your ZTE phone and wait for 5 seconds. After that, connect the phone with PC while long holding the (Volume Down) keys at the same time.
-Once the phone is detected, you must see new driver list on the popup window, from there, select that driver and click to “Install” option.
-Once the installing process is completed. Simply, unplug your phone from PC.
-Let’s move on for frp bypass process.
-Click at > Service > Reset FRP.
| Note: Phone is not detected?, check out troubleshooting tips |
Connect to PC & Remove FRP
-Afterwards, reconnect ZTE device again in the same way by long holding (Volume Down) key and connect to PC.
-Once the phone is detected by the tool, you will the frp bypass process will continue and you will have a (FRP RESET END) message there. That means, you are all done from bypass frp ZTE Nubia Music.
| Note: FRP is not bypassed, check out troubleshooting tips |
-Simply, disconnect the phone from PC and complete setup wizard steps.
| Note: If your device stuck on loading screen and its not completing, you just hard reset your phone by going into the (Recovery Mode). After that, try to finish up setup wizard steps after connecting to WiFi network. |
-If you face the (Google sing in) screen again, don’t worry, you will have a (Skip) option there as well, just skip this screen and continue finishing up all remaining steps.
FAQs: Troubleshooting Tips (If the FRP is not Bypassed)
| Q1: My device is not being detected by PC and BFT Tool. This might be due to not installation of the proper (SPD Drivers).
Solution 1: Download & Install (SPD drivers) manually from below on your computer. After that, repeat all frp bypass steps.
|
| Q2: All drivers are installed properly, but getting (Sync error) and FRP is not done yet.
Solution 2: You try with other chipset name changing from the bft tool. Firstly change chipset name to[AUTH] SC9863A. After that, disconnect phone and click again on “Reset FRP” button and reconnect your phone again with PC by long pressing volume down key. If same issue occurs, then, try changing to Tiger T610 (64). Try again. If nothing happen, then, try with Tiger T606 (64) V2
|
Conclusion
We just got the (BFT tool) on computer and installed it. After that, launched this tool and downloaded SPD and libusb drivers for our ZTE Nubia Music phone. Once its done, simply, connected the phone to PC and clicked at “Reset FRP” button. Within few seconds, we removed the FRP lock protection and completed setup wizard steps easily. We also have mentioned (Troubleshooting tips), if the phone is not detected or frp is not bypassed.