Searching for a straightforward solution to resolve the access problem on your smartphone after conducting a hard reset? The loss of access and encountering (Google Verification) following a hard reset occurs because the FRP lock protection has been enabled. You can only get past this screen if you know your previously configured Gmail account. If not, you will need to either recover your lost Gmail account or refer to the guide provided below to Bypass FRP TCL 502.
Disclaimer: We strongly advise that you use this procedure exclusively on your own device. If you do not own the device, or if it was found, you should return it to its rightful owner. This method is intended solely for educational purposes.
Bypass FRP TCL 502 [By BFT Software]:
-There is a link below, just click on that and download (BFT Software) on your computer.
Note: Remember, don’t forget to disable your any active (@ntivirus) software, other, you may not be able to use the downloaded (BFT software).
| ⇒ BFT Tool V1.7 [DOWNLOAD]. |
-Good thing is that, you don’t need to pay any charge for using the PC software. Simply, click at the “Login” option from popup window to start launching the software interface on your PC/Laptop.
-Finally, go to on the top left corner and set up the processor “0-UNISOC”.
-After that, select “Manual” option and set up the chipset “[AUTH] SC9863A (64)”. Refer to image below for better understanding.
Time to Download SPD Drivers
-Click on the top right corner at “Driver” option. This will collapse down further and show you list of drivers name to download.
-From there, choose “Install SPD Driver.” and wait until downloading is done. After that, install it.
-Click again on “Driver”. Then, go to “Install LibUSB Filter Driver”. Once the downloading is completed, simply, install it as well on PC.
Install Driver through LibUSB
-After installing the (LibUSB filter driver) driver, you will have a popup window of (libusb-win32), from there, go to > Install a device filter > Next.
-Turn off the TCL 502 device. Connect it to PC while long pressing the (Volume Down) button. By doing this, the libusb-win32 will auto detect your phone driver and show you on its popup box list.
-Select that driver and go for the installation process by click to “Install”.
Note: Any driver, you see on the libusb box, these all are missing drivers, you can install all of them and they will disappear from here.
-After its completed, disconnect TCL phone.
Go for FRP Bypass Process
-Hit over the “Service” tab from the BFT Software screen.
-Afterwards, click at “Reset FRP” option.
Note: Is your phone not detected? check out the troubleshooting steps.
-Once you get the green message of connect to computer on your BFT tool, just connect the TCL device with PC by long pressing the (Volume Down) button.
-After that, within few seconds, your device will be detected by the phone and frp bypass procedure will start.
-At the end, you will see message of (FRP RESET END). That means, you are all done now. Disconnect your phone from PC.
Note: If frp is done yet or you are facing connectivity issue, check out our FAQ section.
-Turn on your device and go for completing the setup wizard steps.
-If your device is stuck on any loading page and its not completing even after 4-5 minutes wait. Simply, put your TCL 502 phone into recover mode. After that, hard reset your device by selecting the (Wipe Data/Factory Reset) option.
-Complete setup wizard steps again. This time, you will reach on the (Google Verification) screen. From there, go to > Skip > Skip.
FAQs About TCL 502 FRP Bypass Issues:
| Q1: My device is not being detected by the PC. Answer 1: Download and install SPD drivers manually on computer.
Q2: FRP is reset by the bft tool successfully, my phone is stuck on loading after while completing setup wizard steps. Answer 2: Turn off your phone. Put your device into the (Recovery Mode) screen. After that, hard reset your TCL 502 phone and complete setup wizard steps again.
Q3: Getting SPD drivers error while installation on my Windows 10 and 11 Answer 3: Check our this post. For this, you will have to make some configuration on your computer to install SPD drivers without facing any error. |
The Bottom Line:
We recently obtained the BFT application on our computer and proceeded to install it. Following the installation, we opened this application and acquired SPD and libusb drivers for our ZTE Nubia Music mobile device. After this was completed, we connected the mobile device to the computer and pressed the “Reset FRP” button. In just a few moments, we successfully eliminated the FRP lock protection and navigated through the setup wizard without any difficulties. We have also outlined troubleshooting suggestions in case the device is not recognized or if the FRP bypass is unsuccessful.